Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:5015 [2022/02/17 08:58] – chrissy
+++ internal:proddocs:5015 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 6: / Line 6: @@
 Then using a small file, modify the cut out holes to suit the PCB.
 Mark the corners of the cut out as seen in pictures below**
 {{:internal:proddocs:5015.1.png|}} {{:internal:proddocs:5015.3.png|}}{{:internal:proddocs:5015.5.png|}}{{:internal:proddocs:5015.6.png|}}
 **Select 10851-B touch PCB,  cut 4 x square pieces of foam tape and place in position on either end of the board See pictures below.**
@@ Line 81: / Line 83: @@
 <note important>**Insert connectors, ensure PCB lays flat, when inserting, then insert modified cable connector into PCB, see pics below.**</note>
-{{:internal:proddocs:5015.30.png|}}{{:internal:proddocs:5015.28.png|}}{{:internal:proddocs:5015.29.png|}}
+{{:internal:proddocs:5015.30.png|}}{{:internal:proddocs:5015.28.png|}}{{:internal:proddocs:5015.31.jpg?600|}}
 **Place connector into position from the (203847 cable assembly) see pics below.**
-{{:internal:proddocs:5015.31.png|}}
+{{:internal:proddocs:5015.xxxx.png?600|}}
 <note important>**Unplug 10863 video card cables before programming**</note>
@@ Line 92: / Line 96: @@
 **This is now ready for Programming see information and pics .**
+{{:internal:proddocs:5015.xx.png?600|}}{{:internal:proddocs:5015.35.png?600|}}
   -  Select Atmel studio
@@ Line 111: / Line 118: @@
 {{:internal:proddocs:5015.4.jpg?600|}}
+  - Select memories
+  - Select S:\Code\Production\51xx Poseidon Displays\203090-v1.0.0.hex
+  - Select program
+{{:internal:proddocs:5015.6.jpg?600|}}{{:internal:proddocs:5015.7.jpg?600|}}
+**Connect all cables and it is now ready for testing**
+**Check voltages see pics below.**
+{{:internal:proddocs:5015.33.png?600|}}{{:internal:proddocs:5015.34.png?600|}}
+**Now check Touch button functions see pics below.**
+<note>**Voltage should drop when touch button is pressed**</note>
+{{:internal:proddocs:5015.36.png?600|}}{{:internal:proddocs:5015.37.png?600|}}
+**Using the glue gun place a small amount of glue on connectors in positions highlighted in pics below.**
+**Then place cable clips into position.**
+{{:internal:proddocs:5015.8_li_3_.jpg?600|}} {{:internal:proddocs:5015.9_3_li.jpg?600|}}
+<note warning>**Before the lower back cover is assembled (203390-C), Ensure it fits. After anodizing this often needs adjusting.
+Protect from scratches and place in vice and lift up. repeat this on both ends, see pic below.**</note>
+{{:internal:proddocs:5015..12.png?600|}}
+**Insert connector into position and tighten with correct spanner see pic below.**
+{{:internal:proddocs:5015..11.png?600|}}
+<note important>
+**Screw lower back cover into position using (201074) screws and Loctite 222, do not over tighten see highlighted pic below**</note>
+{{:internal:proddocs:5015..2_li.jpg?600|}}
+<note important>**For the sides of the screen use (203413) screws and loctite 222, do not over tighten, see highlighted pic below.**</note>
+{{:internal:proddocs:5015..3_li.jpg?600|}}
+**Connect leads ready for testing, see pic below.**
+{{:internal:proddocs:5015..32.png?600|}}
+**Connect to laptop and check touch screen functions correctly and picture quality is in good working order, see pics below.**
+{{:internal:proddocs:5015...34.png?600|}} {{:internal:proddocs:5015...33.png?600|}}
+<note important>
+**Assemble upper back cover use (201074) screws and loctite 222 ensure you do not over tighten, see highlighted pic below.**</note>
+{{:internal:proddocs:5015.jpg?600|}}
+**Repeat function test as above.**
+**Now in the clean room, clean the screen ready for silicone.**
+{{:internal:proddocs:5015......png?600|}}{{:internal:proddocs:5015.10.jpg?600|}}
+**Leave to cure overnight, check for holes, clean off any residue.**
+**Select label required and record serial number data, add warranty label.**
+{{:internal:proddocs:5015.222.jpg?600|}}
+**Print manuals and check details, select all products to go with screen.**
+{{:internal:proddocs:5015.666.jpg?600|}}
+<note important>**Place blue film over screen tightly , ensure there is no foreign debris.**</note>
+{{:internal:proddocs:5015.111.jpg?600|}}
+**Wrap screen in bubble wrap, (being careful not to over wrap the ends) this will obstruct the foam inserts.**
+{{:internal:proddocs:5015.333.jpg?600|}}
+**Finally fit labels in place on the final packaging see pic below.**
+{{:internal:proddocs:5015.444.jpg?600|}}
+ --- //[[chrissy@osukl.com|Christine Walsh]] 21/02/2022 09:33//created