Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:3155 [2021/09/22 12:32] – chrissy
+++ internal:proddocs:3155 [2023/11/27 10:16] (current) – kacper
@@ Line 1: / Line 1: @@
-====== 3155 Build Instructions ======
+======3155/9011 Build Instructions ======
 ====== Programming ======
  Modbus to Nmea 2000 gateway flashing guide
-Connect the Modbus gateway to the Atmel AVR ISP via the 6 pin header labled PL2 on the Modbus gatew
+Connect the Modbus to the NMEA Network and STM32 Programmer
-{{:internal:proddocs:3155.png?600|}}{{:internal:proddocs:3155-1.jpg?600|}}
+{{:internal:proddocs:3155setup.jpg?600|}}
-The Pink Stripe on the Connector designates where pin one is located
+Turn on 12V NMEA Power.
-Connect the CAN Power source 12volt from the power supply
-Open AVR Studio 5.1
+{{:internal:proddocs:3155supply.jpg?600|}}
-{{:internal:proddocs:3155_2.png?600|}}
+Open STM32CubeProgrammer and open the programming tab
-Upon opening of AVR Studio 5.1 you will be greeted with these two screens
+{{:internal:proddocs:stm32cubeprogrammer.png?600|}}
-After the program has loaded click “Tools” then “AVR Programming”
-{{:internal:proddocs:3155-4.png?600|}}
-You will then see this screen
+Connect to the Unit and select the file path: S:\Code\Production\3155 Modbus Gateway\3155bootloader.bin
-Select the tool you wish to use for programming your device, in this case we need to use the “AVRISP mkII” so make sure this is selected from the drop down menu.
+{{:internal:proddocs:3155programmingpath.png?600|}}
-Select the device you wish to use, in this case we are using the “Atmel AT90CAN64” so make sure this is selected from the drop down menu.
+click 'Start Programming', the unit should have its blue LED constantly on.
-The interface we will to use is “ISP” (in system programming)
+Open Monex and click "Get Serial" and "Get ProdInfo", you should receive "OCEANIC BOOTLOADER 3155-L4"
-Then Click the Apply button.
+{{:internal:proddocs:monex3155prodinfo.png?600|}}
- {{:internal:proddocs:3155-3.png?600|}}
+Now go to the Programming tab
-After you have clicked Apply this window should now appear.
+{{:internal:proddocs:monexprogrammingtab.png?600|}}
-Set the ISP Clock frequency to 125khz if not already set.
-{{:internal:proddocs:3155-6.png?600|}}
+Make sure the Target Device Instance matched the switch on the unit and click 3155
+{{:internal:proddocs:3155programmingbuttonmonex.png?600|}}
+Press Reprogram! and select S:\Code\Production\3155 Modbus Gateway\3155.bin
+The unit will start to program, wait until "Re-booting to Application Code" is displayed, the unit will not have the Blue led flash every 2 seconds.
+Go into Monex and press 'Get ProdInfo' again, it should display what you can see below:
+{{:internal:proddocs:3155afterproggetprodinfo.png?600|}}
 ====== Test Procedure ======
@@ Line 57: / Line 61: @@
 Connect the USB to RS-485 Converter to the 3155 screw in terminal blocks as shown, tighten with flat head screwdriver (**not too hard**).
-{{:internal:proddocs:modbus_3155.jpg?800|}}
+{{:internal:proddocs:3155modbusconnection.jpg?600|}}
 ==== Step 2 ====
@@ Line 86: / Line 90: @@
 Modbus Mode: RTU
 Slave Address: 16
 Scan Rate: 1000
 Function Code: Read Input Registers (0x04)
-Start Address: 3 (Dec)
+Start Address: 52 (Dec) (**NOTE** For 9011 this value shall be 46)
 Number of Registers: 1
 Data Format: Hex
 {{:internal:proddocs:rtu_readings.png?800|}}
@@ Line 101: / Line 112: @@
 ==== Step 7 ====
+Open Monex, then from the transmit controls on the left, press the "Tx Enable" button for the first sender.
+{{:internal:proddocs:2.png?400|}}
+==== Step 8 ====
 Click the Scan Button
 {{:internal:proddocs:scan_rtu.png?600|}}
-A 4 digit number should appear in the big white box below, it should keep changing value with each new scan.
+A 4 digit number should appear in the big white box below, it should read 0000. Move the slider in Monex to 50 and it should read 30D4. Move the slider to 100 and it should read 61A8.
 {{:internal:proddocs:rtu_value_receive.png?800|}}
-**If a Value is receive succesfully and keeps changing value then testing is completed**
+Now test the modbus configuration by setting the Hex switch on the 3155 to '6'. Press a magnet up to the reed swith, the Blue led should light solid blue.
+Set Qmodbus master settings again to 4,800 Baudrate, Odd Parity, 1 stop bit
+{{:internal:proddocs:3155-6-settings.png?600|}}
+the hex switch should have been left on '6', so now change the slave address to 22
+{{:internal:proddocs:3155-slaveaddress22.png?600|}}
+Request the data again and the data shown should be the same as above
+**If a Values are received successfully then testing is completed - RETURN SWITCH TO 0 AND PRESS MAGNET TO DEVICE TO RETURN TO DEFAULT SETTINGS**
+==== Packaging ====
+Use RPT112  with Insert 200374
+{{:internal:proddocs:3155..2.jpg?600|}}
+ --- //[[chrissy@osukl.com|Christine Walsh]] 23/09/2021 08:41// updated