Oceanic Docs

User Tools

Site Tools

Trace: • 3501 • 3271-sam2 • 3130 • 5200 • 4291 • 4521 • 5170 • 3185 • 3165 • 3125
internal:proddocs:3165

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
internal:proddocs:3165 [2022/10/06 07:00] – kacperinternal:proddocs:3165 [2023/07/12 14:33] (current) – external edit 127.0.0.1
Line 41: Line 41:
   * Device will program, CRC will say 'PASS' and then it will read 'Re-booting to application code' You can now close the dialog   * Device will program, CRC will say 'PASS' and then it will read 'Re-booting to application code' You can now close the dialog
   * Proceed to testing.   * Proceed to testing.
-<note tip>If the blue light fails to light switch PSV off and back on again. If it still does not light, check the polarity of the LED. The cathode (K) is marked by a small dot on the silkscreen.</note>+<note tip>If the green or red light fails to light switch PSV off and back on again. If it still does not light, check the polarity of the LED. The cathode (K) is marked by a small dot on the silkscreen.</note>
  
 ====== Test Procedure ====== ====== Test Procedure ======
Line 59: Line 59:
 === Rudder Angle Testing - (180 - 0 Ohms)  === === Rudder Angle Testing - (180 - 0 Ohms)  ===
  
-  * Connect a resistance box to the space connectors using a wire with a crimped ends on on end (crocodile clips can be used, though they are much more inaccurate.+  * Connect a resistance box to the space connectors using Crocodile Clips.
  
 {{:internal:proddocs:3165_res_box.jpg?600|}} {{:internal:proddocs:3165_res_box.jpg?600|}}
Line 79: Line 79:
   * **Set the resistance box to 180 Ohms** - The Rudder angle should be 45 degrees.   * **Set the resistance box to 180 Ohms** - The Rudder angle should be 45 degrees.
  
-=== Rudder Angle Testing - (240 - 30 Ohms)  === +=== Deflection Angle Testing ===
- +
-  * Set the rotary switch to 'A' and put a magnet onto the Reed Switch to set the Sender into the American Standard. - The Red Led should turn solid when the setting is changed. +
- +
-{{:internal:proddocs:3165_american_setting.jpg?600|}} +
- +
-  * Calibrate the sender first by setting the resistance to 230 Ohms, then setting the instance switch to '4' and putting a magnet to the reed switch. +
- +
-{{:internal:proddocs:3165_port_cal.jpg?600|}} +
- +
-  * Calibrate the sender again by setting the resistance box to 30 Ohms, then setting the instance switch to '5' and putting a magnet to the reed switch. +
- +
-{{:internal:proddocs:3165_stbd_cal.jpg?600|}} +
- +
-  * **Set the resistance box to 230 Ohms** - The Rudder angle should be -45 degrees. +
-  * **Set the resistance box to 130 Ohms** - The Rudder angle should be 0 degrees. +
-  * **Set the resistance box to 30 Ohms** - The Rudder angle should be 45 degrees. +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
  
 +  * Change the Deflection angle to 60 degrees by setting the rotary switch to '9' and pressing a magnet up to the reed switch
  
 +{{:internal:proddocs:3165_rudder_angle_60.jpg?600|}}
  
 +  * **Set the resistance box to 10 Ohms** - The Rudder angle should be -60 degrees.
 +  * **Set the resistance box to 95 Ohms** - The Rudder angle should be 0 degrees.
 +  * **Set the resistance box to 180 Ohms** - The Rudder angle should be 60 degrees.
  
 +  * Return the deflection angle to the default 45 degrees by setting the rotary switch to '8' and pressing a magnet up to the reed switch
  
 +{{:internal:proddocs:3165_rudder_angle_45.jpg?600|}}
  
   * Set the Rotary switch back to '0'.   * Set the Rotary switch back to '0'.
Line 170: Line 127:
 Connect to Monex and assign serial number to the units using the set serial function. Connect to Monex and assign serial number to the units using the set serial function.
  
-{{:internal:proddocs:3130..1.jpg?600|}}+**ADD PICTURE OF LABELLED UNIT**
  
 ====== Packaging ====== ====== Packaging ======
 Use RPT108 and bubble bag Use RPT108 and bubble bag
  
-{{:internal:proddocs:3130..2.jpg?600|}}{{:internal:proddocs:3130..3.jpg?600|}}+**ADD PICTURE OF PACKAGING FINISHED FOR 3165 (BOX)**
  
  --- //[[chrissy@osukl.com|Christine Walsh]] 28/02/2022 08:52//updated potting and packaging.  --- //[[chrissy@osukl.com|Christine Walsh]] 28/02/2022 08:52//updated potting and packaging.
internal/proddocs/3165.1665039606.txt.gz · Last modified: 2023/07/12 14:11 (external edit)
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki