Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:3185 [2022/09/12 08:00] – chrissy
+++ internal:proddocs:3185 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 17: / Line 17: @@
 **Connect the J1939 to NMEA2000 adapter RJ-11 jack to the MPLAB ICD 3 RJ11 connector **
-{{:internal:proddocs:3185..1.png?600|}}
+{{:internal:proddocs:3185..1.png?600|}}{{:internal:proddocs:3185..2.png?600|}}
+**CAN Network power connection**
+**Connect the J1939 to NMEA2000 adapter to the CAN network power source using the CAN connector**
+{{:internal:proddocs:3185..3.png?600|}}{{:internal:proddocs:3185..4.png?600|}}
+**Open MPLAB IPE**
+{{:internal:proddocs:3185..5.png?600|}}
+**Now configure MPLAB IPE to the correct settings for interfacing with the J1939 to NMEA2000 adaptor**
+{{:internal:proddocs:3185..6.png?600|}}
+**Ensure the values are correct then press connect**
+{{:internal:proddocs:3185..7..png?600|}}
+**Then select the Hex file you wish to load by clicking the browse button**
+**This dialogue should then appear to enable you to select a Hex file for programming**
+{{:internal:proddocs:3185..8.png?600|}}
+**
+The location of the Hex files for this particular product is located in S:\Code\Production\3185 J1939 to NMEA2000 Adaptor
+**
+**Double check that you have selected the correct Hex file and it has been loaded successfully**
+{{:internal:proddocs:3185..9.png?600|}}
+**
+Once you are satisfied the correct Hex file has been selected and loaded successfully you can then proceed to program the J1939 to NMEA2000 adaptor.
+Press the Program button
+**
+**Keep an eye on the console output window for feedback on how the programming procedure is running.
+At the end of the programming procedure you will be greeted with a Programming/Verify complete message.
+**
+**You can again verify what has been programmed by pressing the verify button**
+**Once MPLAB IPE has verified the programmed hex you will be greeted with a message in the output console
+**
+**At this point programming and verification on this device (J1939 to NMEA2000 adaptor) is now complete you may now disconnect the CAN power connector and the MPLAB ICD 3 RJ-11 connector.
+{{:internal:proddocs:3185.1.png?600|}}
+====== Testing Procedure======
+Select the test equipment from the shelf
+{{:internal:proddocs:3185..10.png?600|}}
+Get this test equipment from the shelf
+Using test lead, fit 3x wires
+White / black / blue
+Connect the J1939 simulator
+Note –you will require 3 cables from the network to do the test,
+Once this is connected, the green LED will also flash rapidly.
+{{:internal:proddocs:3185..11.png?600|}}
+Image with all 3 cables connected below.
+{{:internal:proddocs:3185..12.png?600|}}
+See pic below for program.
+{{:internal:proddocs:3185..13.png?600|}}
+Check all instances again
+Check the up / down buttons, as long as the values change the unit is ok.
+This completed programming and test.
+Add 4x 200943 spacers to existing studs in metalwork.
+Place the board 10262 in to the housing. Remove the rubber grommet and nut from PL1.
+{{:internal:proddocs:3185..14.png?600|}}
+Screw 201485 onto studs using the 5mm long socket securing the board to the housing.
+Taking time to align the two switches with the top cover.
+{{:internal:proddocs:3185..15.png?600|}}
+Place the rear cover 201030 on to the unit and screw down using screw 201074 making sure the countersunk holes are facing outwards towards you.
+{{:internal:proddocs:3185..16.png?600|}}
+Once the backing plate is secured, place the Oceanic Systems product description and serial number sticker onto the unit side panel square and central as shown.
+{{:internal:proddocs:3185-16.png?600|}}
+This can now be packed into its box with sleeve and QC label.