Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:3271-sam2 [2022/09/13 11:29] – chrissy
+++ internal:proddocs:3271-sam2 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 3: / Line 3: @@
 <note warning>**The 3271-SAM2 PCB assembly contains components that are sensitive to electrostatic discharge (ESD) – please make sure you are wearing your wrist strap when handling.**</note>
-**Load software - Connect to Atmel Flip system version 2.4.6. Select Menu then the file marked 3271_SAM2_v200.hex, Check it has the latest version software on S\Code\Software version matrix.
+====== 3271-SAM-2 Programming Instructions ======
-Click on USB plug Icon at top of menu from this select CAN / PEAK, from this Menu Click Initiate then node connect. Un-tick box marked BLJB. Click Run this will load the software to the PCB.
-**
+Connect unit to programming device.
-{{:internal:proddocs:sam2.1.png?600|}}{{:internal:proddocs:sam2.2.png?600|}}
+{{:internal:proddocs:sam2_conn_prog.jpg?600|}}
+  * Select STM32CubeProgrammer
+  * Connect to Unit
+{{:internal:proddocs:connect.jpg?600|}}
+  * Select Device programming
+{{:internal:proddocs:inkedprogramming_tab.jpg?600|}}
+  * Browse and select the S:/Code/Production/3271-SAM2/3271-SAM2-Bootloader
+{{:internal:proddocs:sam2bootloaderdirectory.png?600|}}
+    * Click Start Programming Making sure all the checked boxes are correct
+{{:internal:proddocs:sam2progbootloaderfinished.png?600|}}
+You can now disconnect the unit, if programming unsucessful, erase the device memory and try again.
+  * Open Monex and click 'Get Serial' and 'GetProdInfo', you should see the following
+{{:internal:proddocs:sam2monexprodinfo.png?600|}}
+  * Go to the Programming tab and match the device instance to the Target Select
+{{:internal:proddocs:targetprog.png?600|}}
+  * Click on 3271-SAM2 and the Reprogram on the pop-up
+  * Select S:/Code/Production/3271-SAM2/3271-SAM2
+{{:internal:proddocs:sam2programsoftware.png?600|}}
+  * The Device should start programming and should 'PASS', and Reboot to Application Code
+  * Go Back to Device Info Tab and check that Model ID now shows as Sender Averaging Module
+{{:internal:proddocs:sam2prodinfoafterprog.png?600|}}
+====== 3271-SAM-2 Testing ======
 **Conect PCB into Monex.
@@ Line 36: / Line 75: @@
 {{:internal:proddocs:sam2.5.png?600|}}
-**Assembly.
+  * Test If device instance changes when hex switch rotated for all values 0-F.
-Remove M12 nut (retain for later).
+====== Assembly ======
-Remove rubber grommet – this can be disposed of as it is not required.
-**
-{{:internal:proddocs:sam2.6.png?600|}}
-**Fit standoffs so that the PCB sits at the correct height in the plastic case**
-{{:internal:proddocs:sam2.7.png?600|}}
-**Potting: fill the box just under half way, this allows the potting to seep over the edge of the PCB as it’s pushed into the potting.**
-{{:internal:proddocs:sam2.8.png?600|}}
-**Then fill the potting to the shoulder of the switch. Take care not to cover the LED’s during this phase.**
-{{:internal:proddocs:sam2.9.png?600|}}
-**Allocate serial number and print label**
-{{:internal:proddocs:sam2.10.png?600|}}
-**use a bubble bag to protect the unit. Pack into RPT 108 box, with sleeve.**
-{{:internal:proddocs:sam2.11.png?600|}}
+===== Fit PCB to box – this will go either way round =====
+{{:internal:proddocs:sam2casepic.jpg?600|}}
+<note warning>Cover With Epoxy, ensure the LED’s and switches are not covered with epoxy and that the epoxy is smooth and looks professional, if in any doubt ask for a second opinion</note>
+<note important>
+The Adaptor is now ready for Labels, Connect to monex for serial numbers</note>
+Fit top label
+{{:internal:proddocs:4291potted.jpg?600|}}
+====== Manual Printing Instructions ======
+  - Go to (S) Drive.
+  - Parts Documents.
+  - Select 3271-SAM2
+  - Select PDF's.
+  - Select 3271-SAM2 user manual and print.
+====== Label  Printing Instructions ====
+  - Choose labels required
+  - Select (LabelDirect)
+  - Close (Pop Up)
+  - Go to file-open
+  - Select - Parts documents
+  - Select - 3271-SAM2
+  - Select - Labels
+  - Select Correct Label
+  - Highlight Serial number and change in Text box.
+  - Go to Incrementing number Properties and change serial number.
+  - Go to file -Print Setup
+  - Calibrate the label.
+====== Packaging ======
+  * Use RPT103 box
+  * 2 parts insert 203613
+  * Outer sleeve
+  * Contents 1 x 3271-SAM2 Sender Averaging Module
+  * 1 x User Manual
+{{:internal:proddocs:4291-13.png?600|}}