Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:3271-sam2 [2023/06/21 07:07] – kacper
+++ internal:proddocs:3271-sam2 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 3: / Line 3: @@
 <note warning>**The 3271-SAM2 PCB assembly contains components that are sensitive to electrostatic discharge (ESD) – please make sure you are wearing your wrist strap when handling.**</note>
-====== 3271-SAM 2 Programming Instructions ======
+====== 3271-SAM-2 Programming Instructions ======
 Connect unit to programming device.
@@ Line 45: / Line 45: @@
   * Go Back to Device Info Tab and check that Model ID now shows as Sender Averaging Module
+{{:internal:proddocs:sam2prodinfoafterprog.png?600|}}
+====== 3271-SAM-2 Testing ======
+**Conect PCB into Monex.
+This should light up 3 LED’s.
+Blue Tx which pulses,
+A and B will be solid red lights.
+**
+**Set instances as per picture below**
+{{:internal:proddocs:sam2.3.png?600|}}
+**Set fluid type and buttons as per picture below.**
+{{:internal:proddocs:sam2.4.png?600|}}
+**Use 2x sliders to check averaging is working.
+This picture shows below, “8” set to 75% and “9” set to 25%, so the average is 50. Try on a couple of other values. LED’s on PCB should now be as follows:
+Tx LED will flash blue, and A and B will both be flashing green
+**
+{{:internal:proddocs:sam2.5.png?600|}}
+  * Test If device instance changes when hex switch rotated for all values 0-F.
+====== Assembly ======
@@ Line 74: / Line 92: @@
+===== Fit PCB to box – this will go either way round =====
+{{:internal:proddocs:sam2casepic.jpg?600|}}
+<note warning>Cover With Epoxy, ensure the LED’s and switches are not covered with epoxy and that the epoxy is smooth and looks professional, if in any doubt ask for a second opinion</note>
+<note important>
+The Adaptor is now ready for Labels, Connect to monex for serial numbers</note>
+Fit top label
+{{:internal:proddocs:4291potted.jpg?600|}}
+====== Manual Printing Instructions ======
+  - Go to (S) Drive.
+  - Parts Documents.
+  - Select 3271-SAM2
+  - Select PDF's.
+  - Select 3271-SAM2 user manual and print.
+====== Label  Printing Instructions ====
+  - Choose labels required
+  - Select (LabelDirect)
+  - Close (Pop Up)
+  - Go to file-open
+  - Select - Parts documents
+  - Select - 3271-SAM2
+  - Select - Labels
+  - Select Correct Label
+  - Highlight Serial number and change in Text box.
+  - Go to Incrementing number Properties and change serial number.
+  - Go to file -Print Setup
+  - Calibrate the label.
+====== Packaging ======
-{{:internal:proddocs:sam2.1.png?600|}}{{:internal:proddocs:sam2.2.png?600|}}
+  * Use RPT103 box
+  * 2 parts insert 203613
-**Conect PCB into Monex.
+  * Outer sleeve
-This should light up 3 LED’s.
+  * Contents 1 x 3271-SAM2 Sender Averaging Module
+  * 1 x User Manual
-Blue Tx which pulses,
-A and B will be solid red lights.
-**
-**Set instances as per picture below**
-{{:internal:proddocs:sam2.3.png?600|}}
-**Set fluid type and buttons as per picture below.**
-{{:internal:proddocs:sam2.4.png?600|}}
-**Use 2x sliders to check averaging is working.
-This picture shows below, “8” set to 75% and “9” set to 25%, so the average is 50. Try on a couple of other values. LED’s on PCB should now be as follows:
-Tx LED will flash blue, and A and B will both be flashing green
-**
-{{:internal:proddocs:sam2.5.png?600|}}
-**Assembly.
-Remove M12 nut (retain for later).
-Remove rubber grommet – this can be disposed of as it is not required.
-**
-{{:internal:proddocs:sam2.6.png?600|}}
-**Fit standoffs so that the PCB sits at the correct height in the plastic case**
-{{:internal:proddocs:sam2.7.png?600|}}
-**Potting: fill the box just under half way, this allows the potting to seep over the edge of the PCB as it’s pushed into the potting.**
-{{:internal:proddocs:sam2.8.png?600|}}
-**Then fill the potting to the shoulder of the switch. Take care not to cover the LED’s during this phase.**
-{{:internal:proddocs:sam2.9.png?600|}}
-**Allocate serial number and print label**
-{{:internal:proddocs:sam2.10.png?600|}}
-**use a bubble bag to protect the unit. Pack into RPT 108 box, with sleeve.**
+{{:internal:proddocs:4291-13.png?600|}}
-{{:internal:proddocs:sam2.11.png?600|}}