Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:4166 [2023/02/24 14:36] – eral
+++ internal:proddocs:4166 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 10: / Line 10: @@
 Select 4166.
-select offshore_159.
+Select offshore_160.
 S:\Binaries for Embedded\4166
@@ Line 34: / Line 34: @@
 <note important>For Princess software use the same process above but select 4166-P2  (offshore_ 152) S:\Binaries for Embedded\4166-P2</note>
-<note>Where no shake proof washer is fitted, Thread lock is to be used.</note>
 **Before commencing build, program 10823 Dual Engine PCB and TX6Q module.**
 === Programming Instructions 10823 Dual Engine PCB===
@@ Line 159: / Line 159: @@
   - Power off board
-Programming Completed
+Programming Completed.
 ===== Electronic Assembly =====
+<note>Where no shake proof washer is fitted, Thread lock is to be used.</note>
 <note warning>Fit resistor 201331 to the Dual Engine PCB to location VDD. Fit on the top two pads as this is the configuration for the 4166 variant
@@ Line 173: / Line 175: @@
-===== QC CHECK =====
+===== QC CHECK & Mechanical Assembly =====
 - Ensure the external surfaces of the case are clean and not scratched – reject if they are damaged in any way.
@@ Line 196: / Line 198: @@
 <note>If you are fitting the new shorter length connector (202317). Please see Instructions below</note>
-Insert connector all the way into the board. And solder the connector leads flush to the board. Led the soldering iron to stay couple of seconds on each soldering point to allow solder to flow nicely inside the hole.
+Insert connector all the way into the board. And solder the connector leads flush to the board. Let the soldering iron to stay couple of seconds on each soldering point to allow solder to flow nicely inside the hole.
 {{:internal:proddocs:img_20230113_111530.jpg?600|}}{{:internal:proddocs:img_20220808_123653_1_.jpg?600|}}
@@ Line 213: / Line 215: @@
 Fit Dual Engine PCB
-<adm warning>Before fit Dual Engine PCB to the back case cut the long leads as much as possible, shown as below picture.</adm>
+<adm warning>Before fit Dual Engine PCB to the back case cut the long leads as much as possible (in the red circle), shown as below picture.</adm>
 {{ :internal:proddocs:cutting_leads_1.jpg?nolink&600 |}}
 Align with pins on CAN PCB and DSUB connector.
@@ Line 239: / Line 241: @@
 Place TFT into bezel – note the orientation of the cables with the bezel cut out.</note>
-Fit 4x holding screws M2 x 6 203186 (loosely)
+Fit 4x holding screws M2 x 6 203186
-Flip upside down (carefully) so that the screws are at their maximum travel.
-<note important>Then, tighten the screws so the TFT is just above the internal step of the bezel (this is very important)</note>
-{{:internal:proddocs:4166-12.png?600|}}
+{{:internal:proddocs:img_20230224_132941.jpg?600|}}{{:internal:proddocs:img_20230224_133008.jpg?600|}}
-Cut two thin double sided strips and stick to the two longest edges.
+Apply double sided tape and stick to the four edges to prevent dust entering from back side gaps and to ensure better protective glass sticking.
-{{:internal:proddocs:4166-13.png?600|}}
+{{ :internal:proddocs:dust_gap_between_tft_and_frame_1.jpg?nolink&600 |}}
 Solder TFT wires to Dual Engine PCB.
@@ Line 255: / Line 255: @@
 Fit LVDS cable to TFT and J1 on Dual Engine PCB
-Use Takpak on both ends to help hold the cable in place.
+Use one small drop hot glue on both ends to help hold the cable in place.
 {{:internal:proddocs:4166-15.png?600|}}