Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:6010 [2022/05/30 16:20] – created ryan
+++ internal:proddocs:6010 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
 ====== 6010 Build Instructions ======
-<note warning>The Compute Module 4 contains components that are sensitive to electrostatic discharge (ESD) – please make sure you are wearing your wrist strap when handling.</note>
+==== 10902-A Build Instructions ====
+Cut the Ribbon cable to required width and then cut the length to 90mm see pic below.
+Attach the connector and slide into position, see pic below
+{{:internal:proddocs:10902-2.jpg?600|}}
+Crimp both ends into place, see pics below
+{{:internal:proddocs:10902-3.jpg?600|}}{{:internal:proddocs:10902-4.jpg?600|}}{{:internal:proddocs:10902-5.jpg?600|}}
+{{:internal:proddocs:10902-1.jpg?600|}}
+<note>Ensure connectors are crimped correctly, see finished assembly pic below.</note>
+{{:internal:proddocs:img_20220804_112117_1_.jpg?600|}}
+<note warning>The Raspberry Pi 4 contains components that are sensitive to electrostatic discharge (ESD) – please make sure you are wearing your wrist strap when handling.</note>
 ==== Tools Required ====
@@ Line 14: / Line 32: @@
 ==== Build Instruction ====
-  - Using scissors, trim the mounting plate included with the case to remove 10mm of plastic from the right side.
+  - Using scissors, trim the mounting plate included with the case to remove 10mm of plastic from the right side. The arrow points to the left side. {{ :internal:proddocs:6010-pimount.jpg?400 |}}{{ :internal:proddocs:6010-cut.jpg?400 |}}{{ :internal:proddocs:6010-1.jpg?400 |}}
+<note>secure double sided tape to the plastic casing before Raspberry PI is placed into position</note>
   - Attach the Raspberry Pi to the plate with the included screws
   - Remove the plastic coating from the sticky adhesive in the case and use this to affix the Pi into the left side of the case
-  - Trim the through hole on the PSU assembly and apply double sided adhesive tape, affix to the right side of the case
+  - Trim the through hole components on the PSU assembly and apply double sided adhesive tape, affix to the right side of the case
-  - Solder the wire to the solder points as pictured
+  - Solder the wire to the solder points as pictured {{ :internal:proddocs:6010-3.jpg?400 |}}
-  - Connect the ribbon cable
+==== 10902-A Build Instructions ====
+Cut the Ribbon cable to required width and then cut the length to 90mm see pic below.
+Attach the connector and slide into position, see pic below
+{{:internal:proddocs:10902-2.jpg?600|}}
+Crimp both ends into place, see pics below
+{{:internal:proddocs:10902-3.jpg?600|}}{{:internal:proddocs:10902-4.jpg?600|}}{{:internal:proddocs:10902-5.jpg?600|}}
+{{:internal:proddocs:10902-1.jpg?600|}}
+  - Connect the ribbon cable and attach the heatshield using it's sticky pad {{ :internal:proddocs:6010-ribbon.jpg?400 |}}
+<note warning>Ensure ribbon cable is not folded over the heatsink, it must fold over the black PSU</note>
+<note>Cut cable (200584) to 1M (1000mm) and strip both ends.</note>
   - Put the grommet into the hole on the case and feed the wire through
-  - Use a cable tie on the wire on the inside of the case as pictured
+  - Use a cable tie on the wire on the inside of the case as pictured {{ :internal:proddocs:6010-2.jpg?400 |}}
-  - Attach the top half of the case
+  - Attach the top half of the case and pull through the slack on the cable, so that the cable tie prevents the cable being pulled any more.
-  - Insert the SD card
+  - Insert the SD card {{ :internal:proddocs:6010-sd.jpg?400 |}}
   - Affix the label
@@ Line 39: / Line 80: @@
   - Connect the power and apply 24V
   - Turn on, after 20 seconds Poseidon will have loaded
-  - Ensure that the touch screen responds to touch
+  - Ensure that the touch screen responds to touch, see pics below.
+{{:internal:proddocs:6010.2.jpg?400|}}{{:internal:proddocs:6010.3.jpg?400|}}
+{{:internal:proddocs:6010.4.jpg?400|}}{{:internal:proddocs:6010.5.jpg?400|}}
+Packaging
+Place warranty label over SD card slot.
+{{:internal:proddocs:6010.1.jpg?600|}}
+coil cable loosely and place cable ties in position, place in a large bubble bag.
+use RPT 103 box with sleeve, see pics below.