Oceanic Docs

User Tools

Site Tools

Trace: • 3501 • 3271-sam2 • 3130 • 3125 • 3165 • 5200 • 4291 • 3185 • 4521 • 5170
internal:proddocs:3165

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
internal:proddocs:3165 [2022/10/06 06:26] – kacperinternal:proddocs:3165 [2023/07/12 14:33] (current) – external edit 127.0.0.1
Line 41: Line 41:
   * Device will program, CRC will say 'PASS' and then it will read 'Re-booting to application code' You can now close the dialog   * Device will program, CRC will say 'PASS' and then it will read 'Re-booting to application code' You can now close the dialog
   * Proceed to testing.   * Proceed to testing.
-<note tip>If the blue light fails to light switch PSV off and back on again. If it still does not light, check the polarity of the LED. The cathode (K) is marked by a small dot on the silkscreen.</note>+<note tip>If the green or red light fails to light switch PSV off and back on again. If it still does not light, check the polarity of the LED. The cathode (K) is marked by a small dot on the silkscreen.</note>
  
 ====== Test Procedure ====== ====== Test Procedure ======
Line 57: Line 57:
 {{:internal:proddocs:3165_device_instance.png?600|}} {{:internal:proddocs:3165_device_instance.png?600|}}
  
-=== Rudder Angle Testing ===+=== Rudder Angle Testing - (180 - 0 Ohms)  ===
  
-  * Connect a resistance box to the space connectors using a wire with a crimped ends on on end (crocodile clips can be used, though they are much more inaccurate.+  * Connect a resistance box to the space connectors using Crocodile Clips.
  
 {{:internal:proddocs:3165_res_box.jpg?600|}} {{:internal:proddocs:3165_res_box.jpg?600|}}
  
-  * Go to the 'Rudder' tab on Monex, you should be able to see this (instance matching that on yor device):+  * Calibrate the sender first by setting the resistance to 180 Ohms, then setting the instance switch to '5' and putting a magnet to the reed switch.
  
-{{:internal:proddocs:3165_rudder_tab.png?600|}}+{{:internal:proddocs:3165_stbd_cal.jpg?600|}}
  
-  * Set The resistance box to 10 Ohms +  * Calibrate the sender again by setting the resistance box to 10 Ohms, then setting the instance switch to '4' and putting a magnet to the reed switch.
-  * The Rudder angle should be -45 degrees.+
  
 +{{:internal:proddocs:3165_port_cal.jpg?600|}}
  
 +  * Go to the 'Rudder' tab on Monex, you should be able to see this (instance matching that on yor device):
  
-{{:internal:proddocs:8-3130.jpg?600|}} +{{:internal:proddocs:3165_rudder_tab.png?600|}}
- +
-  * **IF THE BLUE LED DOESNT LIGHT IMMEDIATELY THEN TURN THE SUPPLY OFF AND STOP TESTING** +
-  * The Blue LED should turn on and stay on, wait approxmiately 10 seconds. +
- +
-{{:internal:proddocs:5-3130.jpg?600|}} +
- +
-  * Turn the supply off and wait for the Blue LED to turn off and return to normal operation (this can take up to 30 seconds) +
-  * Connect a power supply to the pins on the PCB **AS SHOWN BELOW, PAY ATTENTION TO THE POLARITY OF THE CONNECTION!** +
- +
-{{:internal:proddocs:6-3130.jpg?600|}} +
- +
-  * Set the voltage to 1.0V, turn the supply on.  +
- +
-{{:internal:proddocs:9-3130.jpg?600|}} +
- +
-  * **IF THE BLUE LED DOESNT LIGHT IMMEDIATELY THEN TURN THE SUPPLY OFF AND STOP TESTING** +
-  * The Blue LED should turn on and stay on, wait for approximately 10 seconds. +
- +
-{{:internal:proddocs:5-3130.jpg?600|}} +
- +
-  * turn the supply off and **wait for the Blue LED to turn off** and return to normal operation (this can take up to 30 seconds). +
-  * Set the voltage to 30 - 32V, turn the supply on. +
- +
-{{:internal:proddocs:8-3130.jpg?600|}} +
- +
-  * **IF THE BLUE LED DOESNT LIGHT IMMEDIATELY THEN TURN THE SUPPLY OFF AND STOP TESTING** +
-  * The Blue LED should turn on and stay on, wait approxmiately 10 seconds. +
- +
-{{:internal:proddocs:5-3130.jpg?600|}} +
- +
- +
- +
- +
- +
-=== Resistive Output Testing === +
- +
-* Connect a multimeter in resistance measuring mode across the 2 pins on the PCB +
- +
-{{:internal:proddocs:1-3130.jpg?600|}} +
- +
-  * Go to the 'Volumetric Mode' +
- +
-{{:internal:proddocs:2.png?600|}} +
- +
-  * Under 'Level Transmit Controls' set the left most instance to '0' and the fluid type to 'FUEL', then click 'TxEnable'. +
- +
-{{:internal:proddocs:3.png?600|}} +
- +
-  * Set the rotary switch to 'A' and put a magnet on the reed switch, the Blue LED should light for 2.5 seconds. +
-  * Now return the rotary switch to '0', the Blue LED should be double flashing every 2.5 seconds. +
- +
-{{:internal:proddocs:2-3130.jpg?600|}} +
- +
-  * Change the level to transmit 100%, The measured resistance will state 30 Ohms +
-  * Change the level transmit to 0%, The measured resistance will state 240 Ohms +
-  * Change the level transmit 50%, The measured resistance will state 135 Ohms +
- +
-{{:internal:proddocs:5.png?600|}} +
- +
-  * Now, set the rotary switch to 'F', the LED should be off and the measured resistance will be 30 Ohms+
  
-  * Set the rotary switch to 'E', the LED should remain off and the measured resistance will be 240 Ohms.+  * **Set the resistance box to 10 Ohms** - The Rudder angle should be -45 degrees. 
 +  * **Set the resistance box to 95 Ohms** - The Rudder angle should be 0 degrees. 
 +  * **Set the resistance box to 180 Ohms** - The Rudder angle should be 45 degrees.
  
-  * Set the rotary switch to 'E' and put a magnet on the reed switch, the Blue LED should light for 2.5 seconds. +=== Deflection Angle Testing ===
-  * Now return the rotary switch to '0', the Blue LED should be single flashing every 2.5 seconds.+
  
-{{:internal:proddocs:3-3130.jpg?600|}}+  * Change the Deflection angle to 60 degrees by setting the rotary switch to '9' and pressing a magnet up to the reed switch
  
-  * Change the level to transmit 100%, The measured resistance will state 180 Ohms +{{:internal:proddocs:3165_rudder_angle_60.jpg?600|}}
-  * Change the level transmit to 0%, The measured resistance will state 0 Ohms +
-  * Change the level transmit 50%, The measured resistance will state 90 Ohms+
  
-{{:internal:proddocs:5.png?600|}}+  * **Set the resistance box to 10 Ohms** - The Rudder angle should be -60 degrees. 
 +  * **Set the resistance box to 95 Ohms** - The Rudder angle should be 0 degrees. 
 +  * **Set the resistance box to 180 Ohms** - The Rudder angle should be 60 degrees.
  
-  * Now, set the rotary switch to 'F', the LED should be off and the measured resistance will be 180 Ohms+  * Return the deflection angle to the default 45 degrees by setting the rotary switch to '8' and pressing a magnet up to the reed switch
  
-  * Set the rotary switch to 'E', the LED should remain off and the measured resistance will be 0 Ohms.+{{:internal:proddocs:3165_rudder_angle_45.jpg?600|}}
  
   * Set the Rotary switch back to '0'.   * Set the Rotary switch back to '0'.
Line 185: Line 127:
 Connect to Monex and assign serial number to the units using the set serial function. Connect to Monex and assign serial number to the units using the set serial function.
  
-{{:internal:proddocs:3130..1.jpg?600|}}+**ADD PICTURE OF LABELLED UNIT**
  
 ====== Packaging ====== ====== Packaging ======
 Use RPT108 and bubble bag Use RPT108 and bubble bag
  
-{{:internal:proddocs:3130..2.jpg?600|}}{{:internal:proddocs:3130..3.jpg?600|}}+**ADD PICTURE OF PACKAGING FINISHED FOR 3165 (BOX)**
  
  --- //[[chrissy@osukl.com|Christine Walsh]] 28/02/2022 08:52//updated potting and packaging.  --- //[[chrissy@osukl.com|Christine Walsh]] 28/02/2022 08:52//updated potting and packaging.
internal/proddocs/3165.1665037616.txt.gz · Last modified: 2023/07/12 14:11 (external edit)
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki