Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:3350 [2021/06/23 15:00] – [Printing Labels] chrissy
+++ internal:proddocs:3350 [2025/05/16 09:34] (current) – [Packaging] david
@@ Line 5: / Line 5: @@
 ====== Programming Instructions ======
+<note important><note warning> Any old revision boards need to be programmed using (FLIP)</note></note>
+  * Select device: AT89C51CC03
+  * Select: 3350-Wv200.hex  (Water)
+  * Select: 3350-Fv200.hex (Fuel)
+  * Select: 3350-Gv200.hex (Grey water)
+  * Select 3350-HTPO.200.hex (black)
+  * Select: CAN,
+  * Select : PEAK
+  * Select: INIT
+  * Select: Connect
 {{:internal:proddocs:33501-1.png|}}
+<note important> All new revision boards use Atmel</note>
   -   Open Atmel Studio.
   - ATMEL PROGRAMMING
   - FUSES: All off except BOOTRST and SPIEN
-  - BOOTSIZE = 4096_7800
+  - BOOTSIZE = 2048_7800
   - CKSEL = 16KCK/14CK +64ms (Last option)
   - Then program the fuses.
@@ Line 22: / Line 34: @@
   - Disconnect the PCB
+<note>HTPO on monex is Black when testing</note>
 ====== Assembly Procedure ======
@@ Line 28: / Line 41: @@
 <note important> note correct orientation. One side has 5 pins the other has 6. (The header pins may need to be trimmed down by approx 3 mm to allow better fitment of the outer casing.)
 </note>
-The unit is now connected to the Monex system to check the LED Function @100% and 88% this ensures that all LED bars required to illuminate are lit, and check the Alarm Light function.
+The unit is now connected to the Monex system to check the LED Function @100% and 88% this ensures that all LED bars required to illuminate are lit, and check the Alarm Light function. Check the lights dim when the sensor is covered. Check the alarm works at below 20% for Fuel and Fresh water, and at above 80% for Grey and Black water.
 {{:internal:proddocs:3350-2.png|}}
@@ Line 83: / Line 96: @@
 ===== Printing Manual Instructions =====
   - Go to (S) Drive.
   - Parts Documents.
@@ Line 89: / Line 103: @@
   - Select 3350_user manual and print.
+<note warning>Ensure manual is checked for packaging contents</note>
 ===== Printing Labels =====
   * - Choose labels required
@@ Line 97: / Line 112: @@
   *   - Select - 3350
   *   - Select - Labels
-  *   - Select -  UL_3350-F_vA-1.0.0.0 (fuel)
+  *   - Select - UL_3350-F_vA-1.0.0.0 (fuel)
-  *  - Select UL_3350-BW_vA-1.0.1 (black water)
+  *  - Select -  UL_3350-BW_vA-1.0.1 (black water)
-  * -  Select  UL_3350-W_vA-1.0.0.0 (water)
+  * -  Select -  UL_3350-W_vA-1.0.0.0 (water)
-  * -  Select  UL_3350-GREY_vA-1.0.1 (Grey water)
+  * -  Select  - UL_3350-GREY_vA-1.0.1 (Grey water)
   *   - Highlight Serial number and change in Text box.
   *   - Go to Incrementing number Properties and change serial number.
@@ Line 106: / Line 121: @@
   *   - Select bradyBBP11-34L(copy 1) and select Calibrate.
   *   - label will calibrate.
+===== Inspection =====
+  *   Check serial number label is correct.
+  *   Ensure all parts are present.
+  *   Check for visual damage.
+  *   Ensure the unit works on Monex and test the alarm.
+===== Packaging =====
+  * 1 x Manual
+  * Use RPT103 box
+  * Insert 203406
+  * Sleeve 203371
+{{:internal:proddocs:3350-10.jpg?200|}}
+{{:internal:proddocs:3350-11.jpg?200|}}
+ --- //[[david@osukl.com|David Whittle]] 16/05/2025 10:34// updated