Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:3410 [2022/04/06 07:33] – chrissy
+++ internal:proddocs:3410 [2026/05/18 08:00] (current) – updated current values via notes to account for equipment aging zbigniew
@@ Line 8: / Line 8: @@
 **Connect PCB and set voltage to 12.30 then Select Atmel studio, see pics below**
 {{:internal:proddocs:3410..1.jpg?600|}}{{:internal:proddocs:3410.2.jpg?600|}}
@@ Line 50: / Line 51: @@
-<note>**With the power off, Fit 3410 in place, wire unit as per order below,
+**With the power off, Fit 3410 in place, wire unit as per order below,
 Plug in NMEA connector, Plug in power wires black (1) and red (2). (This is power from the NMEA, not the Power Supply, use grey cable)
-Please see pic below.
+Please see pics below.
+**
-{{:internal:proddocs:3410.7.png?600|}}
+{{:internal:proddocs:3410.7.png?600|}}{{:internal:proddocs:3410.5.png?600|}}
-Connect red (8) and black (7) shunt wires as per label see pics below**</note>
+<note>Connect red (8) and black (7) shunt wires  see pics below.</note>
+{{:internal:proddocs:3410.6.png?600|}}{{:internal:proddocs:3410.14.jpg?600|}}
+**Power up**
+**Try Setting Power Supply to 8.6v. The voltage will fluctuate slightly**
+**Check Voltage of NMEA power supply and record. (Right hand terminals of the power
+supply on the test bench (eg. 12.15V see pics below below))**
+{{:internal:proddocs:3410.11.png?600|}}
+**Set rotary switch to “B”
+Hold button down for 5 seconds until the blue LED lights for 2 seconds
+Set rotary switch to “C”
+Hold button down for 5 seconds until the blue LED lights for 2 seconds
+Set rotary switch to “0”
+Push lever forward all the way see pic below.
+**
+{{:internal:proddocs:3410.15.jpg?600|}}
+**Now, we need to match up values from the DC Monitor tab in Monex
+Check the voltage is the same as recorded in the previous procedure, see pic below.**
+<note important>** For this, the current should MATCH what's on the power supply. If the screen shows 50, PSU should also say 50 +/-3 **</note>
+{{:internal:proddocs:3410.16.png?600|}}
+<note important>**For the 3412 test, Disconnect the red (8) and black(7), shunt wires
+Wire up to 3412, passing blue cable through transformer 3 times.
+Black (3)
+White (5)
+Green (4)
+Red (6) see pic below**</note>
+{{:internal:proddocs:3410.17.png?600|}}
+**Toggle power of PSU in front of you.
+(Turn off and on again). see pic below**
+{{:internal:proddocs:3410.18.png?600|}}
+{{:internal:proddocs:3410.19.png?600|}}
+<note important>** For this, the Current on screen should be about 3.2 times the current on the PSU, +/-5 . For example
+on screen - 50 on PSU, 130 on screen - 40 on PSU etc.  **</note>
+**End of test**
+<adm warning>Add x6 pcs 203017 slim washers to connector PL1 before placing it inside black plastic housing.</adm>
+{{:internal:proddocs:img_20230626_143339.jpg?600|}} {{:internal:proddocs:img_20230626_143350.jpg?600|}}
+**Fit PCB to case – remove plastic grommet from PL1**
+**Fit 203017 shim washer between PL1 nut and case.**
+**Fit base plate – ensure all holes line up for fixings**
+**The base plate is to be glued in place
+**
+add pics here
+**Packaging**
+add pics