Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:3501 [2021/09/22 08:45] – chrissy
+++ internal:proddocs:3501 [2023/12/04 13:19] (current) – kacper
@@ Line 2: / Line 2: @@
 <note warning>The 3501 PCB assembly contains components that are sensitive to electrostatic discharge (ESD) – please make sure you are wearing your wrist strap when handling.</note>
-Solder wires to PCB and insert cable tie into position see pic below
+{{:internal:proddocs:3501.jpg?600|}}
-{{:internal:proddocs:3501-1.jpg?600|}}
 ====== Programming ======
-Select device programming on Atmel Flip and load hex file required.
+Connect the unit to 24V NMEA power as shown
+{{:internal:proddocs:3501_nmea.jpg?600|}}
+Connect the STM32 Programmer to the unit as shown
+{{:internal:proddocs:3501_stm_prog.jpg?600|}}
+Open STM32 Programmer and go into the programming tab
+{{:internal:proddocs:3501_stm_programming_tab.png?600|}}
+Select the 'File Path' to be S:/Code/Production/3501/3501Bootloader
+{{:internal:proddocs:3501_code_bootloader.png?600|}}
+Click "Connect" in the top right corner and make sure all the boxes are checked as shown below and click "Start Programming"
+{{:internal:proddocs:3501_bootloader_programming.png?600|}}
+You can now remove the STM32 programmer from the PCB, the Blue LED should be solid blue.
+Now Open Monex Software (found in S:/Code/Published PC Programs/Monex3
+On the Device Info Tab click, 'Get Serial' and 'Get PodInfo', you should see the following:
+{{:internal:proddocs:3501_monex_prodinfo.png?600|}}
+Go To the 'Programming' Tab and click on 3501, and then on 'Reprogram!' on the pop-up that appears
+{{:internal:proddocs:3501_repro_pop-up.png?600|}}
+Then select vessel for which the unit will be used from S:/Code/Production/3501/....
+For Testing Purposes PEARL62 is used:
+{{:internal:proddocs:3501_pearl62.png?600|}}
+The Programming will begin, wait until "Re-booting to Application Code" is displayed before you begin testing
+{{:internal:proddocs:3501_rebooting_to_app_code.png?600|}}
+====== Testing ======
+Using Monex seet up the level transmit controls as shown below:
+{{:internal:proddocs:3501_test_1.png?600|}}
+The received Level value should be 57.08% (red bar on the right of Monex)
-{{:internal:proddocs:3501-2.jpg?600|}}{{:internal:proddocs:3501-9.jpg?600|}}
+The top left and top middle LED's should be flashing green every 2.5 seconds, and the blue LED should also be flashing every 2.5 seconds.
+Change the level values to the ones shown below:
+{{:internal:proddocs:3501_test_2.png?600|}}
+The received Level value should be 51.29% (red bar on the right of Monex)
+Go to the Device Info tab and change the Hex switch value on the PCB, monitor Device Inst Upper/Lower to make sure it matches the switch value.
+====== Packaging ======
+Use a RPT112 box and a 200374 insert
+{{:internal:proddocs:3501-18.jpg?600|}}{{:internal:proddocs:3501-21.jpg?600|}}
+ --- //[[chrissy@osukl.com|Christine Walsh]] 17/01/2022 08:12// updated