Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:5180 [2022/04/11 11:29] – chrissy
+++ internal:proddocs:5180 [2023/09/26 12:12] (current) – ryan
@@ Line 23: / Line 23: @@
 {{:internal:proddocs:5180.3.png?600|}}
-{{:internal:proddocs:5180.4.png?600|}}
+{{:internal:proddocs:5180....png?600|}}
 {{:internal:proddocs:5180.5.png?600|}}
@@ Line 71: / Line 71: @@
 {{:internal:proddocs:5180.12.png?600|}}
-<note tip>**Ensure jumpers are in desired locations – note, at this point the PCB has NOT been fitted to the case see pics below.**
+<note tip>**Ensure jumpers are in desired locations – note, at this point the PCB has NOT been fitted to the case see pics below.**</note>
   - **Image 1: 1 jumper**
@@ Line 107: / Line 107: @@
 {{:internal:proddocs:5180.18.png?600|}}
 **Fit SATA to FDD cable 203115 and SATA data cable 203125**
 {{:internal:proddocs:5180.19.png?600|}}
 **
 Fit front panel then motherboard 202926. Use wide headed screws x4.**
@@ Line 147: / Line 150: @@
 Note – nut has a flat edge.
 Ensure notch is at the top of M12.**</note>
+<note important>**CAN CONNECTOR CABLE SOLDERING DIFFERS IF YOU HAVE NEW VERSION OF CAN BOARD. PLEASE CHECK BELOW FOR CHANGES.
+**</note>
+{{ :internal:proddocs:4166_can_board_update.jpg?nolink |}}
+{{ :internal:proddocs:img_20230418_083138.jpg?nolink |}}
 **See below pic.**
@@ Line 156: / Line 166: @@
 Black: pin no. 3.**
+<note>**Drawing is shown from the rear aspect as per photo above**.</note>
+**Fit red / black cable supplied with PSU. From 2 pin header on 203130 to yellow header on motherboard. Add cable tie to secure in place, see pic below.**
+{{:internal:proddocs:5180.26.png?600|}}
+<note warning> **Ensure the black and red cable from PSU to the motherboard is fixed down with tak tak at BOTH ENDS so it cannot work loose, see pic below.**</note>
+{{:internal:proddocs:5180.27.png?600|}}
+**Add 2x side plates – screw holes to be near top side, see pic below.**
+{{:internal:proddocs:5180.28.png?600|}}
+<note warning>**Heat sink assy. Unpack heat pipes CAUTION these are filled with liquid so handle with care.  this is quite fiddly and needs care and attention. Ensure all excess heat sink compound is cleaned up.**</note>
+**
+After this, tidy up cables as needed with cable ties- ensure cables are safely routed and not touching the heat pipes. Ensure no cabling is pulled tight as it could dislodge a connector, see pic below.**
+{{:internal:proddocs:5180.29.png?600|}}
+<note important>FINAL QC CHECKS
+**A member of staff (not the person that assembled the units) must check over all the cabling to ensure everything is connected and that no connectors or cables are suffering undue stress – check how cable ties are affecting this.
+Check that the PSU to motherboard cable has been secured with tak pak.
+Check that screws have been tightened sufficiently.
+Check that the cabling is clear of the heat pipes.**</note>
+====== **Final test** ======
+**Temporarily fit lid into place, this is now ready for final programming and test.**
+<note warning>**This is currently done in Engineering, see below for Instructions.**
+</note>
+**Items required
+  - Poseidon unit
+  -
+  - Installer USB stick
+  -
+  - Keyboard and mouse
+  -
+  - Monitor with HDMI connection
+  -
+  - Ethernet cable**
+**Plug in HDMI to HDMI 1.
+Plug in Ethernet cable to ETH1.
+Plug in keyboard and mouse to any USB.
+Plug in USB stick.
+Plug in green power connector.**
+<note>**When power is connected, various lights will come on inside the unit. The auto installer will then run – this will take approximately 5 minutes. When this has finished successfully, it will advise that the installation is complete.**</note>
+{{:internal:proddocs:5180.30.png?600|}}
+**Remove the USB stick, and press enter.**
+**Remove and re insert the power cable – this will prompt the following screen:**
+**Press enter.**
+{{:internal:proddocs:5180.31.png?600|}}
+**This will then give more text as per image – request unlock disc. Press 1 then enter. see pic below**
+{{:internal:proddocs:5180.32.png?600|}}
+**This will then do various scrolling, then ask for a log in prompt, see pic below:
+**
+**"OEM" then enter
+"root" then enter
+**
+{{:internal:proddocs:5180.33.png?600|}}
+**Next type: /opt/install/setup.sh then press enter see pic below**
+{{:internal:proddocs:5180.34.png?600|}}
+**Type serial no then press enter**
+**Type batch ID then press enter**
+**Main server prompt “Y” then enter**
+**see pic below**
+{{:internal:proddocs:5180.35.png?600|}}
+**The system will then continue with the self install.**
+**This will then boot up to the main Poseidon screen. Check that the serial number on the screen ties up with the number on the unit.**
+**Hold down: CTRL + Shift + semi colon, then press “C”
+**
+**Type: candump can0 and press enter**
+**Data will then appear and scroll on the screen, see pic below**
+{{:internal:proddocs:5180.36.png?600|}}
+**Then, press CTRL + “C,”
+Swap the connector to CAN1,
+Type: candump can1 and press enter,
+Data will then scroll as per previous**
+{{:internal:proddocs:5180.37.png?600|}}
+**Press CTRL + “C”**
+**Type: shutdown –t 0 then press enter
+Note the two spaces above!
+The unit will then shut down – add the green connector and box the unit
+**
+**Refit lid using 4 x screws removed earlier. Ensure hands are clean of heat sink compound before doing this, to avoid getting smears on unit.
+Take care not to cross thread these screws, and do not over tighten.**
+**Carefully clean finished box afterwards.
+Fit green connector to mating half on front plate.
+Give the unit a gentle shake to ensure there is nothing loose inside.
+**
+{{:internal:proddocs:5180.38.png?600|}}
+**Fit the void sticker.
+Pack into the box the unit was originally supplied in see pic below.**
+<note important>Ensure the power connector 203134 is FITTED before packing</note>
+{{:internal:proddocs:5180.39.png?600|}}