Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:3130 [2022/02/22 11:33] – [Programming Instructions] ryan
+++ internal:proddocs:3130 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 25: / Line 25: @@
 {{:internal:proddocs:3125-2.png?600|}}
-  * Select Browse, and open the bootloader BIN file from S:\Code\Production\3130 Fuel Sender To Resistive Output Adaptor\3130 Rev A - 2.1.0\Bootloader - Program this first
+  * Select Browse, and open the bootloader BIN file from S:\Code\Production\3130 Fuel Sender to Resistive Output Adapter\Bootloader - Program this first
 ***INSERT IMAGE***
@@ Line 36: / Line 36: @@
   * You can now press disconnect in the top right and remove the TAG CONNECT cable from the board.
-  * Open Monex. MINIMUM MONEX VERSION is 3.10. If you are on a lower version you must update this from S:/Code/Published PC Programs/Monex3
+  * Open Monex. MINIMUM MONEX VERSION is 3.11. If you are on a lower version you must update this from S:/Code/Published PC Programs/Monex3
   * Press 'Get Prod Info' it should read Model ID: OCEANIC BOOTLOADER 3130-L4
-  * Go to the volumetric mode tab and press the reprogram button in the bottom right
+  * Go to the programming tab and press the reprogram button labelled 3310
+{{:internal:proddocs:2022-02-22_11_43_39-monex_3.11_-_nmea2000_programming_tool.png?400|}}
-{{:internal:proddocs:3125-5.png?400|}}
   * Press reprogram on the dialog that has just popped up
-  * Navigate to S:\Code\Production\3125 Tank Sender Adaptor\3125 Rev H - 2.1.0\Main Program - Program this with Monex and select the 3125-2.1.0.bin software and then press Open
+  * Navigate to S:\Code\Production\3130 Fuel Sender to Resistive Output Adapter\Main Program - Program this with Monex - Program this with Monex and select the 3130-2.1.0.bin software and then press Open
   * Device will program, CRC will say 'PASS' and then it will read 'Re-booting to application code' You can now close the dialog
   * Proceed to testing.
@@ Line 85: / Line 83: @@
 {{:internal:proddocs:5-3130.jpg?600|}}
-  * Turn the supply off and wait for the Blue LED to turn on and return to normal operation (this can take up to 30 seconds)
+  * Turn the supply off and wait for the Blue LED to turn off and return to normal operation (this can take up to 30 seconds)
   * Connect a power supply to the pins on the PCB **AS SHOWN BELOW, PAY ATTENTION TO THE POLARITY OF THE CONNECTION!**
@@ Line 160: / Line 158: @@
 **TESTING COMPLETED, IF IN ANY DOUBT ASK DEV**
+=== Potting procedure ===
+**Before potting ensure PCB is flat and level to the casing.**
+need pic here
+<note warning>The bags of Epoxy resin are kept in the potting room - suitable PPE should be worn when using the two-part Epoxy potting compound e.g. rubber gloves, overalls</note>.
+<note>1 x bag is sufficient to fill 6 units.</note>
+ Warm the compound on the heat plate (to approx 35/40°c), this takes approximately 5 minutes. Do not warm above this temperature as it will greatly reduce the pot life of the compound.
+Once warm, work the black potting BEFORE removing the clip and rail – this will help remove any lumps caused by the fillers that have settled over time. Then, put back on to the heat plate for 1 minute.
+Remove the clip and rail, and mix thoroughly for 2 minutes.
+.  Holding the bag vertically snip about 10 mm off the top corner at 45 degrees with a pair of scissors. Now drizzle the Epoxy over the circuit board to a level, taking care not to get any on the LED or Dial face. Allow to harden overnight. This will allow the mixture to settle.
+<note warning> If any bubbles appear, these can be dispersed by gently, for a few seconds using a hot air gun on the lowest setting over the surface.</note>
+The Potting must now be left for 24 hours to cure and harden.
+{{:internal:proddocs:3130.1.jpg?600|}}
+After the units have been removed from the jig, remove any over spill from the jig so it is clean for the next use.
+Once the epoxy potting has cured, the serial number label can be adhered to the potting top of the product as shown. Position carefully,  the label is printed with:
+Product name and part number
+Serial Number
+Hardware and Software level.
+Connect to Monex and assign serial number to the units using the set serial function.
+{{:internal:proddocs:3130..1.jpg?600|}}
+====== Packaging ======
+Use RPT108 and bubble bag
+{{:internal:proddocs:3130..2.jpg?600|}}{{:internal:proddocs:3130..3.jpg?600|}}
+ --- //[[chrissy@osukl.com|Christine Walsh]] 28/02/2022 08:52//updated potting and packaging.