Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:3281 [2022/02/23 12:52] – chrissy
+++ internal:proddocs:3281 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 59: / Line 59: @@
 **The sender is now ready for programming.**
- **   * Connect to Atmel Flip system.   * Select Hex file 3281 check it has the latest version software.  *  Click on USB plug Icon at top of menu from this select PEEK,    * Click Initiate then node connect, see pic below.**
+<note>**Connect the Sender head to the NMEA cable and power on the device
+Connect the ST/LINK v2 to the programming header. You will need the PCB to be loose from the sender head to be able to access it, as it is on the under-side of the board.
+Open STM32CubeProgrammer
+Click the Icon on the left hand side:**** 5) Click the connect button.**</note>
-{{:internal:proddocs:3281.9.png?600|}}
+**Browse to the folder S:\Code\Production\3281 water Level Sender\Program AFTER Rev J\
+Then select 3281bootloader.bin**
-** Un-tick box marked BLJB. Click Run this will load the software to the PCB, see pic below**
-{{:internal:proddocs:3281.10.png?600|}}
+{{:internal:proddocs:3281...jpg?600|}}{{:internal:proddocs:img_20220505_150521.jpg?600|}}
+**Ensure the check boxes are as shown below and then select “Start Programming”**
+{{:internal:proddocs:img_20220506_074850.jpg?600|}}
+<note important>**Now, the blue LED should be on solid.
+Open Monex 3.12, Select the Programming tab, and then press “3281”**
+</note>
+{{:internal:proddocs:img_20220505_150709.jpg?600|}}
+**Press the re-program button**
+{{:internal:proddocs:3271..6.png?600|}}
+**Navigate to S:\Code\Production\3271 Fuel Level Sender\Program AFTER Rev J and select 3271-v5.bin, then press “open”.
+**
+**Browse to the folder S:\Code\Production\3281 water Level Sender\Program AFTER Rev J\
+Then select 3281bootloader.bin**
+**The tool will now indicate it is programming, it will then show a CRC and PASS, and finally will reboot to application code.**
+{{:internal:proddocs:3271..8.png?600|}}
 <note important>**Before potting, allow the senders to acclimatise in the potting room for a couple of hours. This will reduce the chance of any condensation on the inner sender body.**</note>
@@ Line 86: / Line 113: @@
 **At this point, the cotton buds can be removed so the sender is now flat and the sender can be topped up.**
-.
+.{{:internal:proddocs:3281.11.png?600|}}
+The Potting must now be left overnight to
+Cure and harden.
+<note important>**No epoxy to be visible on the switch and overspill is to be wiped away. Epoxy must be flush to metal surface to avoid creating a recess for any fluid to accumulate when in use.**</note>
+{{:internal:proddocs:3281.12.png?600|}}
+**Once the Potting has set, the Serial No Label can be applied. Position symmetrically as shown in pic below.
+The label must show the:
+Part Number
+Serial Number
+Hardware and software level**
+{{:internal:proddocs:3281.13.png?600|}}
+**You are now ready to connect the unit to the Monex system and assign the unit the serial number from the sticker and to do a final test after assembly to make sure the unit is still fully functioning and has not been damaged during the build procedure.
+Click SET SERIAL – input the serial number from the label
+Click GET PRODUCT INFO to confirm Serial Number and software level**
+**Calibrate to Level Mode see instructions below**
+{{:internal:proddocs:3281.15.png?600|}}
+**Calibrating the Level Sender to empty, see information below.**
+{{:internal:proddocs:3281.16.png|}}
+====== Packaging. ======
+**The Sender is now ready for packing. The user instructions are packed into Poly Bag 200332 along with 1 off Cap
+Assy 200310 Place sender in tube with Instructions
+Add  Label  to Packaging Tube  positioned as shown
+Add product indicator label to cap – highlight boxes with product information.
+(To indicate product – Length and settings if required)
+Add 1x 30g tube of silicone sealant 203122 to the contents, even if we have pre cut the length.**
+{{:internal:proddocs:img_20220228_104608.jpg?600|}}{{:internal:proddocs:img_20220228_104708.jpg?600|}}
+**Select product label required and place in position on tube.**
+{{:internal:proddocs:img_20220228_104718.jpg?600|}}
+ --- //[[chrissy@osukl.com|Christine Walsh]] 28/02/2022 11:00//created