Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:5971 [2022/02/28 12:42] – [Testing Procedure] chrissy
+++ internal:proddocs:5971 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 63: / Line 63: @@
 </note>
+**Open the RelayBoardTester Software: and select,
+**
+**S:\Code\Published PC Programs\NavLightTester\RelayBoardTester**
+ **see pic below**
+{{:internal:proddocs:5971.13.png?600|}}
+<note important>**Make sure the Instance is the same as on the PCB
+The ‘Receiving’ tab on RelayBoardTester should be blinking green.**
+</note>
+**On the RelayBoardTester click the ‘Turn ON/OFF’ button for Switch 1 – Switch 4.
+LED 4 – LED 7 on the PCB should turn green.
+The LEDs on the LED testing connector (SK1) should turn on see pic below.
+**
+{{:internal:proddocs:5971.14.png?600|}}
+**Remove the LED testing connector.
+LED 4 – LED 7 on the PCB should turn red.
+When you reconnect the LED testing connector to SK1, LED 4 – LED 7 should turn green again, see pic below**
+{{:internal:proddocs:5971.15.png?600|}}
+<note important>Repeat test for all remaining LED Testing connectors, including the extension board.</note>
+{{:internal:proddocs:5971.16.png?600|}}
+**Replace the 12V power supply into the right 2 holes of SK1.
+(Right most pin – Red)
+(2nd from right pin – Black) see pic below**
+{{:internal:proddocs:5971.17.png?600|}}
+**On the RelayBoardTester, click ‘Toggle All’.
+All the LEDs should light:
+-	Red if LED testing connector is not matching switch number,
+-	Green if LED testing connector matches switch number see pic below.**
+{{:internal:proddocs:5971.18.png?600|}}
+====== Assembly Instructions ======
+**Push 2 Rail Feet onto the Base Extrusion.**
+{{:internal:proddocs:5971.19.png?600|}}
+**Secure one end cover using the self-tapping screw (P/N 203183) and a washer (P/N 201714).**
+{{:internal:proddocs:5971.20.png?600|}}
+**Attach 6 spacers to the PCB (P/N 203641) using 6mm M2.5 Pozi Screw (P/N 201715).**
+{{:internal:proddocs:5971.26.png?600|}}
+**Slide PCB into the Base paying close attention to the Orientation of the Rail Feet!!!**
+{{:internal:proddocs:5971.27.png?600|}}
+**Secure PCB with the 2nd end cover (P/N 203181) using the self-tapping screw (P/N 203183) and a washer (P/N 201714).**
+{{:internal:proddocs:5971.28.png?600|}}
+**Secure 10 Light Pipes in the shown positions (you may need a colour version of the SOP to see).
+Make sure they are all well-fitting and pushed all the way to the PCB.**
+{{:internal:proddocs:5971.29.png?600|}}
+**Apply the Module Cover as shown. Careful not to damage the switches or Light pipes.
+Make sure the buttons are slightly above the case and everything is well fitted this can take some time.
+Secure with 6 M2.5 Torx screws (P/N 203642).**
+{{:internal:proddocs:5971.30.png?600|}}
+**Apply The 5971 Label. Make sure all the LEDs, Buttons and switches are exposed.**
+{{:internal:proddocs:5971.31.png?600|}}
+**Secure NMEA connector with Nut.**
+{{:internal:proddocs:5971.32.png?600|}}
+**Connect 2 8-way mates and 1 4-way mate as shown. (P/N 203537) and (P/N 203670)**
+{{:internal:proddocs:5971-33.png?600|}}
+====== Packaging ======
+**Connect to monex, set serial number and check product info**
+{{:internal:proddocs:5971.24.jpg?600|}}
+{{:internal:proddocs:5971.21.jpg?600|}}{{:internal:proddocs:5971.22.jpg?600|}}
+ --- //[[chrissy@osukl.com|Christine Walsh]] 08/03/2022 14:00//created