Differences

This shows you the differences between two versions of the page.

--- internal:proddocs:5985 [2022/10/06 08:10] – created kacper
+++ internal:proddocs:5985 [2023/07/12 14:33] (current) – external edit 127.0.0.1
@@ Line 35: / Line 35: @@
   * Go to the programming tab and press the reprogram button labelled 5985
-{{:internal:proddocs:3165_prog.png?400|}}
+{{:internal:proddocs:5985_programming.png?600|}}
   * Press reprogram on the dialog that has just popped up
-  * Navigate to S:\Code\Production\3165.bin - Program this with Monex.
+  * Navigate to S:\Code\Production\5985 Can to DMX\CAN to DMX.bin - Program this with Monex.
   * Device will program, CRC will say 'PASS' and then it will read 'Re-booting to application code' You can now close the dialog
   * Proceed to testing.
-<note tip>If the green or red light fails to light switch PSV off and back on again. If it still does not light, check the polarity of the LED. The cathode (K) is marked by a small dot on the silkscreen.</note>
+<note tip>If the blue light fails to light switch PSV off and back on again. If it still does not light, check the polarity of the LED. The cathode (K) is marked by a small dot on the silkscreen.</note>
 ====== Test Procedure ======
-  * Connect the 3165 to a powered NMEA cable.
+  * Connect the 5985 to a powered NMEA cable.
   * Open Monex on your computer, MINIMUM MONEX VERSION is 3.13. If you are on a lower version you must update this from S:/Code/Published PC Programs/Monex3.
-  * Press 'Get Prod Info' it should read Model ID: Rudder Angle Sender
+  * Press 'Get Prod Info' it should read Model ID: CAN to DMX Converter
 === Device Instance Testing ===
@@ Line 55: / Line 55: @@
   * Monitor the Device instance reported by Monex and make sure it matches the Rotary switch instance.
-{{:internal:proddocs:3165_device_instance.png?600|}}
+{{:internal:proddocs:5985_device_instance_test.png?600|}}
-=== Rudder Angle Testing - (180 - 0 Ohms)  ===
-  * Connect a resistance box to the space connectors using Crocodile Clips.
-{{:internal:proddocs:3165_res_box.jpg?600|}}
-  * Calibrate the sender first by setting the resistance to 180 Ohms, then setting the instance switch to '5' and putting a magnet to the reed switch.
-{{:internal:proddocs:3165_stbd_cal.jpg?600|}}
-  * Calibrate the sender again by setting the resistance box to 10 Ohms, then setting the instance switch to '4' and putting a magnet to the reed switch.
-{{:internal:proddocs:3165_port_cal.jpg?600|}}
-  * Go to the 'Rudder' tab on Monex, you should be able to see this (instance matching that on yor device):
-{{:internal:proddocs:3165_rudder_tab.png?600|}}
-  * **Set the resistance box to 10 Ohms** - The Rudder angle should be -45 degrees.
-  * **Set the resistance box to 95 Ohms** - The Rudder angle should be 0 degrees.
-  * **Set the resistance box to 180 Ohms** - The Rudder angle should be 45 degrees.
-=== Deflection Angle Testing ===
-  * Change the Deflection angle to 60 degrees by setting the rotary switch to '9' and pressing a magnet up to the reed switch
-{{:internal:proddocs:3165_rudder_angle_60.jpg?600|}}
-  * **Set the resistance box to 10 Ohms** - The Rudder angle should be -60 degrees.
-  * **Set the resistance box to 95 Ohms** - The Rudder angle should be 0 degrees.
-  * **Set the resistance box to 180 Ohms** - The Rudder angle should be 60 degrees.
-  * Return the deflection angle to the default 45 degrees by setting the rotary switch to '8' and pressing a magnet up to the reed switch
-{{:internal:proddocs:3165_rudder_angle_45.jpg?600|}}
   * Set the Rotary switch back to '0'.